Table of Content
That’s still a lot, but having to lift three tons less every week will increase production and decrease the risk of injury. VOG is a wallpaper-like coating that’s used in the majority of manufactured homes as it’s lightweight and easier to install than drywall. You’ll notice that VOG has a shiny finish with strips running from the floor to the ceiling, which are used to cover the seams. A sheet of 1/4″ thick drywall that is 4′ x 8′ weighs approximately 38.4 lbs. Drywall that is 5/8″ thick is, of course, a little heavier, at 2.31 pounds per square foot or 73.92 pounds per sheet which is entirely too much for mobile home ceilings.
After material and labor are added in, the cost per panel can range from around $40.00 to $60.00. If you’re looking at older mobile homes, you’re likely to find Vinyl on Gypsum wallboards, and most new manufactured homes have either Paper on Gypsum wallboard or finished drywall options. Various thicknesses of drywall can be used for walls, but usually, most people prefer to go with ½ inch thick drywall to ensure adequate insulation and fire protection. Thicker drywall may be a bit more expensive than most people are willing to pay and might provide far more sound insulation than you bargain for unless this is your goal.
What is the best way to decorate an old mobile home?
This ensures adequate insulation and decent resistance to fire damage, although for another application drywall that is significantly thicker or thinner may be more conducive. Ceiling drywall thickness can vary according to your preference but generally speaking ceiling drywall thickness is roughly 3/8 inches. Again, if you prefer to have more insulation in your ceiling this can vary considerably, but most building codes consider 3/8 inches to be the standard. The kind of drywall we all wish we had when we were teenagers. This type of drywall has the ability to reduce or completely block out external noise depending on your preference. Unlike X-type drywall, it does not do this through its density alone.
Being thin, this type of drywall can be bent and curved around corners, a good example is the base of a spiraling staircase. Although they are extremely useful you should be mindful when handling them as they are quite thin and rigid, which means that they can be brittle. Plaster is a building method which involves applying plaster over narrow wooden strips or a board which is nailed to a vertical frame or wall stud. In addition to being easy to install, drywalls are also one of the most energy-efficient wall materials out there. Drywalls keep the house insulated from the outside which translates into a cooler house during the summer and warm during the winter.
Paper-Free Drywall
Way back in the 1890s, an innovative new construction product called Sackett Board was invented by Augustine Sackett. Now that I’ve got that out of the way let us get more into the details—history, applications, pros, cons—so you can make an informed decision the next time you’re renovating your interiors or exteriors. Upgrades to your manufactured home that make it look more like a site-built home Upgrade to a higher roof pitch.
This size is also commonly used for ceilings as they are durable, long-lasting, and won’t sag over time. Soundproof drywall contains more layers than normal drywall, including wood fibers, polymers, and gypsum. As the name suggests, this type of drywall is used to further isolate noise within a space. Moisture-resistant drywall comes with a special coating that gives it a green shade.
In a mobile home, how do you repair interior walls?
If the studs don’t line up exactly with the edges of the sheet, or there is not enough stud to attach the sheet using screws, use some mobile home drywall adhesive instead. Continue working around each room until the drywall installation is complete. How to hang drywall in a mobile home comes down to two basic choices. Remove all the existing wall panels and attach the drywall to the studs, or attach the new drywall sheets over the existing wall material. Both will give a satisfactory finish, but obviously, the first option involves a lot more work and material that has to be disposed of. Mobile home manufacturers cover walls with panels of vinyl board and fasten them in place with battens.
Older mobile homes with smaller trusses that are 24″ apart cannot handle too much weight. The image below is also from Frugal Farm Wife and shows a single wide that just had its original ceiling panel removed. You’re seeing the vapor barrier with the insulation above.
If you decide to replace the ceiling panels as well, then you should drywall the ceiling before you tackle the walls. This makes for better wall-to-ceiling joints since the wall boards will be secured tight to the ceiling boards. The joints are covered with batten strips during assembly rather than using tape to cover the seams like drywall.
Being thick enough to insulate your home and make it feel cozy, and while being light enough for those installing it to carry it up and downstairs, this thickness of drywall is extremely popular. Panels are available in four drywall thicknesses—5/8-in., 1/2-in., 3/8-in., and 1/4-in. Each drywall thickness has specific applications and framing requirement. Drywall thickness was the most commonly used drywall in new residential construction and remodeling. But, lightweight drywall is rapidly replacing this heavier drywall thickness.
Even easier to carry are ultra-light 1/2-inch panels, which are 13 pounds lighter than conventional 1/2-inch drywall. When wall panels come in lengths and widths other than these multiples of 4 feet, they are usually not drywall panels but are instead cement board or a drywall alternative, such as DRIcor Smartwall. Once all the drywall is complete, re-install all the outlet and wall switch covers. Any molding and baseboards that can’t re-installed will need to be completely replaced. The core on lightweight is a little harder, so utility knife blades do get duller faster when scoring it. And a drywall rep recently told me that because the lightweight drywall has less mass, it’s not as good of a product for sound control as the old version.
Most supply stores will deliver to your home due to the size and weight of the sheets. Although mobile homes are designed to be light, the walls still have wooden studs, and manufacturers will frequently cover the framing with 1/4-inch paneling. The mobile home drywall, which comes in 8 foot by 4 feet sheets, should be easy to install because the wall studs are spaced to support 4-by-8 panels. The next question is how much does it cost to install drywall in a mobile home.
Not sure what the difference in the STC rating is exactly, but it is something to think about. While not every mobile home is the same, there’s a good chance your walls are either drywall or VOG . Your mobile home may have walls made out of wood panels, and if so that probably means it’s quite old.
Mobile home gypsum panels are not smooth, they have a slight texture that most homeowners dislike. Most mobile homes and older manufactured homes have ceilings made of gypsum instead of drywall. The 4-foot by 8-foot size allows for either vertical or horizontal installation. Typically 4 by 8-foot panels come attached in pairs—two sheets face to face, with paper strips binding the two sheets. Most people find it extremely difficult to carry these sandwiched panels by themselves, and they can be difficult to cut.
No comments:
Post a Comment